3-858-368-11 (1)
Video Cassette
Recorder
Operating Instructions
PAL NTSC
SLV-KF295SV
SLV-XF245SV
©1996 by Sony Corporation
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Table of contents
Getting Started
4
5
6
8
Step 1: Unpacking
Step 2: Setting up the remote commander
Step 3: Connecting the unit
Step 4: Tuning your TV to the unit
Basic Operations
10 Playing a tape
Additional Operations
14 Playing/searching at various speeds
16 Karaoke sing-along (SLV-KF295SV only)
19 Adjusting the picture
20 Editing with another VCR
Additional Information
22 Troubleshooting
24 Specifications
25 Index to parts and controls
Back cover
Index
3
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Getting Started
Step 1
Unpacking
Check that you have received the following items with the unit:
• Remote commander
• Mains lead
• Microphone (SLV-KF295SV only)
• R6 (Size AA) batteries
• Aerial cable
• Audio/video cable (3-phono to 3-
phono)
Checking your model name
The instructions in this manual are for the 2 models: SLV-KF295SV
and XF245SV. Check your model number by looking at the rear panel
of your unit. The SLV-XF245SV is the model used for illustration
purposes. Any difference in operation is clearly indicated in the text,
for example, “SLV-KF295SV only.”
4
Getting Started
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Step 2
Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries by
matching the + and – on the batteries
to the diagram inside the battery
compartment.
Using the remote commander
Remote sensor
You can use this remote
commander to operate the unit
and a Sony TV. To operate this
unit, point at the remote sensor
on the unit. To operate the TV,
point at the remote sensor on
the TV.
TV/VIDEO
;
u
PROG(CH) +/–
VOL +/–
To
Press
Turn the TV to standby or active mode
Turn on the TV power
u
;
Increase (+) or decrease (–) the TV volume
Change the TV programme position
VOL +/–
PROG(CH) +/–
Select an input source of the TV either from aerial in or from line in TV/VIDEO
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not mix different types of batteries.
5
Getting Started
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Step 3
Connecting the unit
AERIAL OUT
Aerial cable
AC IN
AERIAL IN
to mains
: Signal flow
1
2
3
Disconnect the aerial cable from your TV
and connect it to AERIAL IN on the rear
panel of the unit.
AERIAL
OUT
IN
AERIAL
OUT
Connect AERIAL OUT of the unit and
the aerial input of your TV using the
supplied aerial cable.
IN
Connect AC IN of the unit to the mains
using the supplied mains lead.
6
Getting Started
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Additional connections
To a TV that has phono type
audio/video input jacks
This unit
TV
AUDIO VIDEO
LINE IN
This additional connection
improves picture and sound quality.
Connect the TV as shown on the
right.
IN
LINE OUT
VIDEO
AUDIO
Audio/video cable (supplied)
Stereo system
This unit
To a stereo system
You can improve sound quality by
connecting a stereo system as
shown on the right.
AUDIO VIDEO
LINE IN
LINE OUT
AUX IN
Audio cable (not supplied)
7
Getting Started
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Step 4
Tuning your TV to the unit
If you have connected your unit to the TV using the audio/video cable, skip
this step.
u (On/Standby)
1
2
Press u (On/Standby) to turn on the unit.
Turn on your TV and select a programme position for video
playback.
Choose a channel between UHF 30 and 39 on the TV where there is
no picture and no sound or only a steady rustling sound.
This channel will now be referred to as the video channel.
3
Insert a tape recorded in the colour system matching your TV into
the cassette compartment.
The unit starts playing automatically if you insert a tape with its
safety tab removed.
4
5
Press · PLAY on the unit.
Tune the TV until the video playback picture is clearly displayed on
the TV screen.
Refer to your TV manual for tuning instructions.
You have now tuned your TV to the unit. From now on, whenever
you want to play a tape, set the TV to the video channel.
If the playback picture does not appear clearly, see “To obtain a clear
playback picture” on page 9.
8
Getting Started
SLV-KF295SV/XF245SV 3-858-368-11 (1)
To obtain a clear playback picture
If the playback picture does not
appear clearly in step 5 above,
turn the RF CHANNEL screw
on the rear panel of the unit
with a screwdriver to a
position where the TV clearly
displays the playback picture.
RF CHANNEL
Selecting the TV system
For your TV to receive the correct
signal from your unit, you must
set the TV SYSTEM switch on the
rear panel of the unit to either G
(for system B/G) or K (for system
D/K). If this switch is set to the
wrong position, the sound will be
distorted.
TV SYSTEM
G
K
9
Getting Started
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Basic Operations
Playing a tape
6 EJECT
P PAUSE
3/#
SEARCH
) FF
· PLAY
p STOP
0 REW
PICTURE
NTSC PB
COLOR SYSTEM
1
2
Turn on your TV and set it to the video channel.
Insert a tape.
The unit turns on, and starts playing
automatically if you insert a tape with its
safety tab removed.
Basic Operations
10
SLV-KF295SV/XF245SV 3-858-368-11 (1)
3
Press · PLAY.
PLAY
When the tape reaches the end, it will rewind automatically.
Additional tasks
To
Press
Stop play
Pause play
p STOP
P PAUSE
Resume play after pause P PAUSE or · PLAY
Search forward
Search backward
Fast-forward the tape
Rewind the tape
Eject the tape
) FF or # SEARCH during playback
0 REW or 3 SEARCH during playback
) FF during stop
0 REW during stop
6 EJECT
To set the colour system
If streaks appear during playback, set COLOR SYSTEM on the unit to
conform to the system that the tape was recorded in. (Normally set the
switch to AUTO.)
If your tape was recorded in
Set COLOR SYSTEM to
PAL/MESECAM
NTSC
PAL
NTSC
MESECAM
PAL/MESECAM
continued
Basic Operations
11
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Playing a tape (continued)
To play an NTSC-recorded tape
Set NTSC PB on the unit according to the colour system of your TV.
If your TV is
PAL
Set NTSC PB to
ON PAL TV
NTSC 4.43
NTSC 4.43
NTSC 3.58
NTSC 3.58
Watching a rental tape
Set PICTURE on the unit to RENTAL PICTURE. Noise will be reduced on
the playback picture. After watching the rental tape, set the switch back to
NORMAL.
Selecting the sound during playback
Press AUDIO MONITOR to
select the desired sound. Each
press of the button changes the
display on the unit. When you
play a tape recorded in stereo
or with a bilingual sound track,
the HiFi indicator on the unit
lights up.
AUDIO MONITOR
To listen to a
Press AUDIO MONITOR until the
display window indicator shows
Stereo tape’s
Bilingual tape’s
“L/R”
“L”
Stereo sound
Left channel
Main and sub sounds
Main sound
Right channel
Standard sound*
“R”
Sub sound
No indication
Standard sound*
* The mixed sound of left and right channels (monaural)
Basic Operations
12
SLV-KF295SV/XF245SV 3-858-368-11 (1)
How sound is recorded on a video tape
The unit records sound onto two separate tracks. Hi-fi audio is recorded
onto the main track along with the picture. Monaural sound is recorded
onto the normal audio track along the edge of the tape.
Stereo
Mixed left/right
Bilingual
Mixed left/right
channels
channels
Normal audio track
(monaural)
Hi-fi audio track
(main track)
Stereo sound
(left/right
Main (left channel)
Sub (right channel)
channels)
Notes
• Depending on your TV, the following may occur while playing an NTSC-recorded
tape:
– the picture is black and white,
– the picture shakes,
– no picture appears on the TV screen,
– black streaks appear horizontally on the TV screen, and
– the colour density increases or decreases.
• To listen to playback sounds in stereo, you must use the AUDIO OUT connections.
• When you play a tape recorded in monaural, the sound is heard in monaural
regardless of the AUDIO MONITOR setting.
• You cannot select the sound to listen to while recording.
• You can playback tapes recorded in the SP mode only.
• You can eject a tape even when the power is off. When you press 6 EJECT, the unit
turns on automatically. After ejecting the tape, the unit turns off again.
• When the pause mode lasts for more than approximately five minutes, the unit will
automatically enter the playback mode.
Basic Operations
13
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Additional Operations
Playing/searching
at various speeds
& SLOW +/–
7 FRAME
· PLAY
0 REW
) FF
3/#
SEARCH
) FF
· PLAY
0 REW
Playback options
Operation
Fast-forward/rewind
During stop, press ) FF or 0 REW.
View the picture during fast- During fast-forward, hold ) FF down. During rewind, hold
forward or rewind
Play at high speed
Play in slow motion
0 REW down.
During playback or pause, press # SEARCH or 3 SEARCH.
During playback or pause, press & SLOW+/–. Press the +/–
buttons to change the speed.
Play frame by frame
Rewind and start play
During pause, press 7 FRAME to advance the picture one frame.
Hold the button down to play one frame each second.
During stop, hold 0 REW on the unit down and press · PLAY
on the unit.
Additional Operations
14
SLV-KF295SV/XF245SV 3-858-368-11 (1)
To resume normal playback
Press · PLAY.
Tip
• If the picture shakes while in the still mode, adjust the picture using $/4
TRACKING NORMAL/SLOW STILLADJUST on the unit.
Notes
• Streaks or snow cannot be eliminated completely in the various playback
operations.
• The sound is muted during these operations.
Additional Operations
15
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Karaoke sing-
along (SLV-
MIC VOL 1
MIC VOL 2
KF295SV only)
You can sing along with a karaoke
videotape, a TV broadcast, or music
played back on equipment connected to
the LINE IN jacks on the rear panel of
the unit. You can sing duets if you use
an extra microphone (not supplied).
MIC IN 1/2
KARAOKE
ON/OFF
· PLAY
ON/OFF
ECHO
Before you start...
Microphone
(supplied)
• Turn on your TV and set it to the
video channel.
• Connect the supplied microphone to
the MIC IN 1 jack. To sing duets,
connect the optional microphone to
the MIC IN 2 jack.
Singing along with karaoke video tapes
1
2
Set KARAOKE ON/OFF to ON.
Insert a karaoke video tape.
The unit turns on and starts playing automatically if you insert a tape
with its safety tab removed.
3
4
Press · PLAY.
If you want to playback a specific song, see “Searching with the AMS
function” on page 17.
Set the ON/OFF switch on the microphone to ON.
Now you can enjoy playing karaoke.
To adjust the microphone volume
Turn the MIC VOL 1 control for the microphone connected to MIC IN 1.
Turn the MIC VOL 2 control for the microphone connected to MIC IN 2.
Setting the MIC VOL 1 and/or 2 control(s) to the centre position provides
the best microphone volume.
To control the echo effect
Turn the ECHO control. This controls both microphones’ echo effect in the
same way.
To get the best effect, adjust the microphone volume to a slightly higher level
than the music volume.
Additional Operations
16
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Reducing the playback vocals (Karaoke Pon)
You can use ordinary music
sources with vocals for karaoke
with this function. Use hi-fi
stereo music sources.
Set KARAOKE PON to ON.
KARAOKE PON
The singer’s voice will be reduced.
To cancel Karaoke Pon
Set KARAOKE PON to OFF.
Searching with the AMS function
The AMS (Automatic Music
Sensor) function searches for
the beginning of the next or
previous song by detecting a
blank space between songs.
Present position
Blank space
1
2
Press p STOP.
Press =/+ AMS.
• To locate the beginning of
the next song, press +
AMS.
=/+
AMS
• To locate the beginning of
the previous song, press
= AMS.
· PLAY
The unit starts searching and
stops automatically when it
locates the beginning of the
next or previous song.
p STOP
3
Press · PLAY to start
playback.
continued
Additional Operations
17
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Karaoke sing along (SLV-KF295SV only) (continued)
Tip
• When you sing along with music played back on equipment connected to the LINE
IN jacks on the unit, play the music source and follow steps 1 and 4 on page 16.
Notes
• If the sound is reproduced through a stereo amplifier, turn down the volume of
amplifier before operation.
• If streaks appear during playback, select the colour system that the tape was
recorded in (see “To set the colour system” on page 11).
• If feedback occurs, turn down the microphone or TV volume, or move the
microphone away from the speakers.
• Karaoke Pon does not work with the following tapes:
– tapes on which different vocal sounds are recorded on the left and right channels,
such as a duet;
– tapes recorded monaurally; or
– tapes on which sound sources are recorded with strong echo effects and chorus
effects.
• The AMS may not work correctly when:
– the tape quality is poor,
– a song is very short (less than 40 seconds),
– the interval between songs is very short (less than 6 seconds),
– a high level sound is recorded between songs or at the beginning of a song,
– there are low level passages or passages without sound in a song,
– narration is recorded at the beginning of a song,
– fade-in or fade-out recording is made on the tape, or
– AMS starts from the very beginning of the tape or near an interval between
songs.
Additional Operations
18
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Adjusting the
picture
Adjusting the tracking
Although the unit
automatically adjusts the
tracking when playing a tape,
distortion may occur if the tape
was recorded in poor
condition. If so, manually
adjust the tracking.
Press $/4 TRACKING
$/4
TRACKING
NORMAL/
SLOW
NORMAL/SLOW to obtain the
best possible picture. The
distortion should disappear as
you press one of the two
buttons. If you cannot get a
clear picture with manual
adjustment, press TRACKING
AUTO/MANUAL to return to
automatic adjustment.
TRACKING
AUTO/
MANUAL
About OPC
OPC (Optimum Picture Control) automatically improves playback quality
by adjusting the unit to the condition of the video heads and tape.
The OPC function automatically works on all types of tapes, including rental
tapes. You can play a tape using the OPC function even if the tape was not
recorded with it.
Notes
• The auto tracking function works automatically when you play back a tape just
after inserting it.
• Sufficient picture quality may not be obtained when playing back tapes recorded on
another VCR or tapes in poor condition.
• When a tape recorded with the copyguard system is played back, intermittent
distortion may appear in the upper portion of the picture. However, this is not a
malfunction of the unit.
Additional Operations
19
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Editing with another VCR
How to connect to record on this unit
TV
This unit (Recorder)
LINE IN
Other VCR (Player)
LINE OUT
VMC-810 audio/video cable (not supplied)
: Signal flow
Tip
• If the other VCR is a monaural type, use a connecting cable like the Sony VMC-
910MS.
Notes
• Make sure you connect the plugs to jacks of the same colour.
• When connecting the units, do not simultaneously connect the LINE IN and LINE
OUT jacks on your unit with the other VCR. A humming noise may occur if you do
this.
Additional Operations
20
SLV-KS295SV/XF245SV 3-858-368-11 (1)
Operation (when recording on this unit)
P PAUSE
You can make a copy of a tape
using this unit for recording or
playback. The unit cannot record
TV programmes directly since it
does not have a TV tuner.
Before you start editing
• Turn on your TV and set it to
the video channel.
r REC
1
Insert a source tape with its safety tab removed into the other
(playback) VCR. Search for the point to start playback and set it to
playback pause.
2
Insert a tape with its safety tab in place into this (recording) unit.
Search for the point to start recording and press P PAUSE.
3
4
Press r REC on this unit to set it to recording pause.
To start editing, press the P PAUSE buttons on both units at the same
time.
To stop editing
Press the p STOP buttons on both units.
To save a recording
To prevent accidental erasure, break off the safety
tab as illustrated. To record on a tape again,
cover the tab hole with adhesive tape.
Auto head cleaner
Safety tab
The unit incorporates an auto head cleaner which
cleans the video heads when a tape is loaded or
unloaded. When the heads are not sufficiently clean, even after a tape has
been loaded/unloaded several times, use the Sony V-25CL video head
cleaning cassette.
Tips
• To edit more precisely, press the P PAUSE buttons on the units to release pause.
• To cut out unwanted scenes while editing, press P PAUSE on this unit when an
unwanted scene begins. When that scene ends, press P PAUSE again to resume
recording.
Note
• You can record tapes only in SP mode.
Additional Operations
21
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Additional Information
Troubleshooting
If you have any questions or problems not covered below, please consult your
nearest Sony service facility.
Symptom
Remedy
The u (On/Standby) switch
does not function.
• Connect the mains lead securely.
The power is turned on but the
unit does not operate.
• Moisture condensation occurs. Turn the power off,
unplug the mains lead and leave the unit to dry for
over an hour.
• The auto safety system is triggered to protect your tape
and the unit’s mechanism when there is something
wrong with the tape or when the mechanism is
overloaded. Press u to restart the unit. If the unit
does not work after pressing u again, disconnect the
mains lead from the mains. Wait for at least 15
seconds. Then reconnect mains, and press u again. If
the unit still does not work, please consult your nearest
Sony service facility.
The VCR enters standby mode
or turns off automatically.
• Make sure the TV is set to the video channel. If you
are using a monitor, set it to video input.
The playback picture does not
appear on the TV screen.
• Adjust the tracking with the $/4 TRACKING
NORMAL/SLOW buttons.
The picture is not clear.
• Make sure the COLOR SYSTEM switch is set to the
position corresponding to the colour system which the
tape was recorded with.
• The video heads are dirty (see below). Clean the video
heads using the Sony V-25CL video head cleaning
cassette. If this cleaning cassette is not available in
your area, have the heads cleaned at your nearest Sony
service facility (a standard service charge will be
required). Do not use a commercially available wet-
type cleaning cassette, as it may damage the video
heads.
• The video heads may have to be replaced. Consult
your local Sony service facility for more information.
• Adjust the vertical hold control on the TV or monitor.
• The tape is defective. Use a new tape.
The picture rolls vertically
during picture search.
The picture has no sound.
Symptoms caused by contaminated video heads
• Normal picture
• Rough picture
• Unclear picture
• No picture (or
black & white
screen appears)
initial
terminal
22
Additional Information
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Symptom
Remedy
The tape starts playing as soon
as it is inserted.
• The safety tab has been removed. To record on this
tape, cover the tab hole.
• Check that the safety tab has not been removed.
The tape is ejected when you
press r REC.
The microphone sound is
distorted. (SLV-KF295SV only)
• The MIC VOL control is set too high.
No tape can be inserted.
• Check that a tape isn’t already in the tape
compartment.
The remote commander does
not function.
• Make sure you are pointing the remote commander at
the remote sensor on the unit.
• Replace all the batteries in the remote commander with
new ones if they are weak.
The unit needs to be cleaned.
• Clean the cabinet, panel, and controls with a dry soft
cloth, or a soft cloth slightly moistened with a mild
detergent solution. Do not use any type of solvent,
such as alcohol or benzine.
Additional Information 23
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Specifications
System
Supplied accessories
RF output signal
Remote commander (1)
UHF channels 30 to 39
Aerial out
R6 (Size AA) batteries (2)
Aerial cable (1)
75-ohm asymmetrical aerial socket
Mains lead (1)
Audio/video cable (3-phono to 3-phono)
Microphone (1) (SLV-KF295SV only)
Inputs and outputs
LINE IN
VIDEO IN, phono jack (1)
Design and specifications are subject to change
without notice.
Input signal: 1 Vp-p, 75 ohms,
unbalanced, sync negative
AUDIO IN, phono jack (2)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
LINE OUT
VIDEO OUT, phono jack (1)
Output signal: 1 Vp-p, 75 ohms,
unbalanced, sync negative
AUDIO OUT, phono jack (2)
Standard output: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
Microphone input
MIC IN 1/2 (2)
more than 3 kilohms, 1.84 mVrms
General
Power requirements
110 – 240 V AC, 50/60 Hz
Power consumption
12W (SLV-KF295SV)
10 W (SLV-XF245SV)
Operating temperature
5°C to 40°C
Storage temperature
–20°C to 60°C
Dimensions
Approx. 355 x 102 x 283.5 mm (w/h/d)
including projecting parts and controls
Mass
Approx. 3.8 kg
24
Additional Information
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Index to parts and controls
Refer to the pages indicated in parentheses ( ) for details.
Front panel (SLV-KF295SV)
HI-FI
REC
L
R
Front panel (SLV-XF245SV)
HI-FI
R
REC
L
!¢ PICTURE switch (12)
!∞ NTSC PB switch (12)
!§ COLOR SYSTEM switch (11)
!¶ Remote sensor (5)
1 u (On/Standby) switch/indicator (8)
2 § EJECT button (11)
3 Tape compartment
4 Tape operation indicators
5 HiFi L/R indicators (12)
6 REC (recording) indicator
7 AUDIO MONITOR button (12)
(SLV-KF295SV only)
!• MIC VOL 1/2 controls (16)
!ª MIC IN 1/2 jacks (16)
@º ECHO control (16)
8
03 REW button (11, 14)
9 · PLAY button (11)
!º )# FF button (11, 14)
!¡ r REC button (21)
@¡ KARAOKE PON (ON/OFF) switch
(17)
@™ KARAOKE (ON/OFF) switch (16)
!™ p STOP button (11)
!£ P PAUSE button (11)
continued
Additional Information 25
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Index to parts and controls (continued)
Rear panel
1 AC IN connector (6)
5 LINE OUT VIDEO/AUDIO L/R
jacks (7)
2 RF CHANNEL screw (9)
3 AERIAL OUT connector (6)
6 AERIAL IN connector (6)
7 TV SYSTEM switch (9)
4 LINE IN VIDEO/AUDIO L/R
jacks (20)
26
Additional Information
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Remote commander (e.g. SLV-KF295SV)
1 6 EJECT button (11)
2 TV/VTR button (This button doesn’t
work for this unit)
3 TV buttons (Only for TV) (5)
TV/VIDEO
; (TV power)
u (Power standby)
VOL +/–
PROG (CH) +/–
4 7 FRAME button (14)
5 TRACKING AUTO/MANUAL
button (19)
6 r REC button (21)
7 P PAUSE button (11)
8 0 REW button (11, 14)
9 p STOP button (11)
!º u (On/Standby) switch (8)
!¡ & SLOW +/– buttons (14)
!™ $/4TRACKING NORMAL/SLOW
STILL ADJUST buttons (19)
!£ =/+ AMS buttons (17) (SLV-
KF295SV only)
!¢ 3/# SEARCH buttons (11, 14)
!∞ · PLAY button (11)
!§ ) FF button (11, 14)
Additional Information 27
SLV-KF295SV/XF245SV 3-858-368-11 (1)
Index
M
A, B
Accessories supplied
Adjusting
Monitoring
4
during playback 12
picture 19
tracking 19
N
Aerial hookup
6
Normal audio track 13
NTSC-recorded tapes 12
AMS searching 17
Audio track 13
Auto head cleaner 21
O
AV connection
7
OPC (Optimum Picture
Control) 19
C
Cleaning the video
heads 22
P, Q
Picture adjustment. See
Adjusting
Playback 10
Colour system
compatible colour
systems
setting 11
Connecting
2
at various speeds 11, 14
frame-by-frame 14
slow motion 14
the VCR and your TV
to a TV with audio/
6
R
video jacks
7
Recording 20
Remote commander
Rental tape 12
RF CHANNEL screw
5
D
Dubbing. See Editing
9
E, F, G
Echo 16
Editing 20
S
Safety tab 21
Searching at various
speeds 14
SP mode 13
H, I, J
Hi-fi audio track 13
T, U, V, W, X, Y, Z
K, L
Tracking adjustment. See
Karaoke sing-along 16
Adjusting
Reducing the playback
vocals 17
Tuning your TV to the
unit
8
TV system
9
Sony Corporation
SLV-KF295SV/XF245SV 3-858-368-11 (1)
|