4-115-660-11(1)
CD/DVD
Player
US
ES
Operating Instructions
Manual de instrucciones
DVP-SR200P
© 2008 Sony Corporation
hour until the moisture
evaporates.
• When you move the player, take
out any discs. If you don’t, the
disc may be damaged.
Notes about the discs
On safety
• To keep the disc clean, handle
the disc by its edge. Do not touch
the surface. Dust, fingerprints, or
scratches on the disc may cause
it to malfunction.
• To prevent fire or shock hazard,
do not place objects filled with
liquids, such as vases, on the
apparatus.
• Should any solid object or liquid
fall into the cabinet, unplug the
player and have it checked by
qualified personnel before
operating it any further.
For the model supplied
with the AC plug adaptor
If the AC plug of your unit does not
fit into the wall outlet, attach the
supplied AC plug adaptor.
On power sources
• The player is not disconnected
from the AC power source as
long as it is connected to the wall
outlet, even if the player itself
has been turned off.
• If you are not going to use the
player for a long time, be sure to
disconnect the player from the
wall outlet. To disconnect the
AC power cord, grasp the plug
itself; never pull the cord.
On adjusting volume
Do not turn up the volume while
listening to a section with very low
level inputs or no audio signals. If
you do, the speakers may be
damaged when a peak level section
is played.
• Do not expose the disc to direct
sunlight or heat sources such as
hot air ducts, or leave it in a car
parked in direct sunlight as the
temperature may rise
considerably inside the car.
• After playing, store the disc in its
case.
• Clean the disc with a cleaning
cloth. Wipe the disc from the
center out.
On cleaning
On placement
US
Clean the cabinet, panel, and
• Place the player in a location
with adequate ventilation to
prevent heat build-up in the
player.
controls with a soft cloth slightly
moistened with a mild detergent
solution. Do not use any type of
abrasive pad, scouring powder or
solvent such as alcohol or benzine.
• Do not place the player on a soft
surface such as a rug.
• Do not place the player in a
location near heat sources, or in a
place subject to direct sunlight,
excessive dust, or mechanical
shock.
• Do not install the player in an
inclined position. It is designed
to be operated in a horizontal
position only.
• Keep the player and the discs
away from equipment with
strong magnets, such as
microwave ovens, or large
loudspeakers.
On cleaning discs, disc/
lens cleaners
Do not use cleaning discs or
disc/lens cleaners (including
wet or spray types). These
may cause the apparatus to
malfunction.
• Do not use solvents such as
benzine, thinner, commercially
available cleaners, or anti-static
spray intended for vinyl LPs.
• If you have printed the disc’s
label, dry the label before
playing.
On replacement of parts
In the event that this unit is
repaired, repaired parts may be
collected for reuse or recycling
purposes.
• Do not place heavy objects on
the player.
Precautions
• Do not install this player in a
confined space, such as a
bookshelf or similar unit.
• Install the player so that the AC
power cord can be unplugged
from the wall socket
IMPORTANT NOTICE
The power requirements and
power consumption of this player
are indicated on the back of the
player. Check that the player’s
operating voltage is identical with
your local power supply.
Caution: This player is capable
of holding a still video image or
on-screen display image on your
television screen indefinitely. If
you leave the still video image
or on-screen display image
displayed on your TV for an
extended period of time you risk
permanent damage to your
television screen. Plasma
immediately in the event of
trouble.
Power requirements and
power consumption
On operation
• If the player is brought directly
from a cold to a warm location,
or is placed in a very damp room,
moisture may condense on the
lenses inside the player. Should
this occur, the player may not
operate properly. In this case,
remove the disc and leave the
player turned on for about half an
m
display panel televisions and
projection televisions are
susceptible to this.
DVP–XXXX
X
00V 00Hz
NO.
00W
0-000-000-00
If you have any questions or
problems concerning your player,
please consult your nearest Sony
dealer.
3US
Table of Contents
About This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 1: Connecting to Your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A Audio/video input jacks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Step 4: Quick Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Various Play Mode Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Adjusting the playback picture (CUSTOM PICTURE MODE) . . . . . . . . . 22
SCREEN SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CUSTOM SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Setting the digital output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4US
Self-diagnosis Function (When letters/numbers appear on the screen) . . . . 34
Parental Control Area Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
About This Manual
• Instructions in this manual describe the controls on the remote. You can also use the controls
on the player if they have the same or similar names as those on the remote.
• “DVD” may be used as a general term for commercial DVDs, DVD+RWs/DVD+Rs/DVD+R
DLs (+VR mode) and DVD-RWs/DVD-Rs/DVD-R DLs (VR mode, video mode).
• NEED-to-know information (to prevent incorrect operation) is listed under the
b
icon. NICE-
to-know information (tips and other useful information) is listed under the
• The meaning of the icons used in this manual is described below:
z
icon.
Icons
Meaning
Functions available for commercial DVDs and DVD+RWs/DVD+Rs/
DVD+R DLs in +VR mode or DVD-RWs/DVD-Rs/DVD-R DLs in video
mode
Functions available for DVD-RWs/DVD-Rs/DVD-R DLs in VR (Video
Recording) mode
Functions available for VIDEO CDs (including Super VCDs or CD-Rs/
CD-RWs in video CD format or Super VCD format)
Functions available for music CDs or CD-Rs/CD-RWs in music CD format
Functions available for DATA discs containing MP3* audio tracks and
JPEG image files
* MP3 (MPEG-1 Audio Layer III) is a standard format defined by ISO (International Organization for
Standardization)/IEC (International Electrotechnical Commission) MPEG which compresses audio
data.
5US
Guide to Parts and Controls
For more information, see the pages indicated in parentheses.
Remote
Turns the TV on or to standby mode.
Turns on, or sets the player to standby
mode.
VOL +/– (11)
Adjusts the TV volume.
B Number buttons
Enters the title/chapter numbers, etc.
CLEAR (17)
Clears the entry field.
Displays the playing time and
remaining time. Press repeatedly to
change the displayed information.
CD/DVD text appears only when text
is recorded on the disc.
If an MP3 audio track has an ID3 tag,
the player will display the album
name/track title from the ID3 tag
information. This player supports ID3
versions 1.0/1.1 and 2.2/2.3.
VOL +, number 5, AUDIO, and N buttons have a
tactile dot. Use the tactile dot as a reference when
operating the player.
AUDIO (
)
Changes the audio language or audio
channel.
Divides the screen into 9 subscreens
so you can choose the desired scene
quickly.
Each time you press the button, the
display changes as follows:
• CHAPTER VIEWER
When 4 digits are displayed, they
indicate a language code. See
see which language the code
represents.
The format of the current audio signal
(Dolby Digital, DTS, PCM, etc.)
appears as shown on page 7.
• TITLE VIEWER
• TRACK VIEWER
The JPEG image files in the album
appear in 16 subscreens.
TV INPUT (input select) (11)
Switches the TV’s input source
between the TV and other input
sources.
6US
Basic operations
When playing a DVD VIDEO
Example:
Dolby Digital 5.1 ch
To
Operation
Press N.
Press x.
Play
Stop
Pause
Rear (L/R)
Press X.
:
3 / 2 .1
ENGLISH DOLBY DIGITAL
1
Go to the next chapter, Press >.
track, or scene in
continuous play mode
LFE (Low Frequency
Effect)
Front (L/R)
+ Center
Go back to the
Press ..
previous chapter,
track, or scene in
continuous play mode
Changes the subtitles.
D TOP MENU
Scan backward/
forward
Press
M
Press repeatedly to
change the speed.
m/
.
Displays the DVD’s top menu.
Displays the menu.
Replay the previous
scene* *
Press
REPLAY during
playback.
1
3
Returns to the previous display.
Briefly fast forward
Press
ADVANCE during
playback.
2
3
DISPLAY (16)
Displays the playback information on
the current scene* *
the screen.
4
Play backward* /
Press X during
playback, then press
m/M
5
forward* in slow
Moves the highlight to select a
displayed item.
motion
repeatedly.
4
Play backward* /
Press X during
5
forward* one frame playback, then press
Enters the selected item.
at a time
/
.
Play in various speed Press FAST/SLOW
E ./> PREV/NEXT
6
with sound*
PLAY repeatedly
during playback.
/
REPLAY/STEP/
1
STEP/ADVANCE
*
For all DVDs except for DVD+RWs/DVD+Rs/
DVD+R DLs.
For DVDs only.
2
3
m/M
N PLAY
X PAUSE
x STOP
(scan/slow)
*
*
These functions may not work with some
scenes.
4
5
6
*
*
*
For DVD VIDEOs and DVD-VR mode only.
For DVDs and VIDEO CDs only.
For DVDs, VIDEO CDs, Super VCDs and
DVD-VR mode only.
FAST/SLOW PLAY
function of each button.
7US
,continued
Front panel
D
Rear panel
PB
VIDEO
L
DIGITAL
OUT
VIDEO OUT
COMPONENT
VIDEO OUT
R
Y
PR
COAXIAL
AUDIO OUT
8US
Hookups
When unpacking, check the supplied accessories by referring to page 36.
b
• Plug cables securely to prevent unwanted noise.
• Refer to the instructions supplied with the components to be connected.
• Be sure to disconnect the power cord of each component before connecting.
Step 1: Connecting to Your TV
Connect this player to your TV monitor using a video cable. Select pattern A or B, according
to the input jack on your TV monitor, projector, or audio component.
INPUT
(white)
A
L
Audio/video cable (supplied)
AUDIO
(red)
R
(yellow)
VIDEO
(red)
(white)
(yellow)
TV
to VIDEO OUT
to AUDIO OUT
P
B
VIDEO
L
DIGITAL
OUT
VIDEO OUT
COMPONENT
VIDEO OUT
R
Y
P
R
COAXIAL
AUDIO OUT
CD/DVD player
to COMPONENT
VIDEO OUT
(green)
(red)
(blue)
COMPONENT
VIDEO IN
B
Y
(green)
Component video
cable (not supplied)
PB
PR
(blue)
(red)
TV
: Signal flow
When connecting to a wide screen TV
Depending on the disc, the image may not fit
your TV screen. To change the aspect ratio,
A Audio/video input jacks
You will enjoy standard quality images.
B Component video input jacks
(Y, PB, PR
)
b
You will enjoy accurate color reproduction
and high quality images.
Do not connect a VCR, etc., between your TV and
the player. If you pass the player signals via the
VCR, you may not receive a clear image on the TV
screen. If your TV has only one audio/video input
jack, connect the player to this jack.
b
Connect the supplied audio cable to audio input
jacks (L/R) on your TV.
9US
,continued
To connect to your audio component
Use the following pattern.
Step 2: Connecting the
Power Cord
CD/DVD player
PB
VIDEO
L
DIGITAL
OUT
VIDEO OUT
COMPONENT
VIDEO OUT
R
Y
PR
COAXIAL
AUDIO OUT
Plug the player and TV power cords into an
AC outlet.
to DIGITAL OUT
(COAXIAL)
DIGITAL
OUT
COAXIAL
Step 3: Preparing the
Remote
Coaxial digital cable
(not supplied)
You can control the player using the supplied
remote. Insert two Size AA (R6) batteries by
matching the 3 and # ends on the batteries
to the markings inside the compartment.
When using the remote, point it at the remote
to coaxial
digital input
Audio component
with a decoder
sensor
on the player.
: Signal flow
z
For correct speaker location, see the operating
instructions supplied with the connected
components.
1
If your audio component has a Dolby*
2
Digital or DTS* decoder and a digital input
jack, use this connection. You can enjoy
Dolby Digital (5.1ch) and DTS (5.1ch)
surround effect.
b
• Do not leave the remote in an extremely hot or
humid place.
• Do not drop any foreign object into the remote
casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light
from the sun or a lighting apparatus. Doing so
may cause a malfunction.
• If you do not use the remote for an extended
period of time, remove the batteries to avoid
possible damage from battery leakage and
corrosion.
*1
Manufactured under license from Dolby
Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #:
*2
5,451,942 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Out are
registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-
2007 DTS, Inc. All Rights Reserved.
b
• After you have completed the connection, make
Otherwise, no sound or a loud noise will come
from your speakers.
• The TVS effects of this player cannot be used
with this connection.
• In order to listen to DTS sound tracks, you must
use this connection. DTS sound tracks are not
output through the AUDIO OUT L/R jacks, even
if you set “DTS” to “ON” in Quick Setup
10US
To control other TVs with the remote
You can control the sound level, input source,
and power switch of non-Sony TVs as well.
If your TV is listed in the table below, set the
appropriate manufacturer’s code.
Controlling your TV with the
supplied remote
You can control the sound level, input source,
and power switch of your Sony TV with the
supplied remote.
1
While holding down TV [/1, press the
number buttons to select your TV’s
manufacturer’s code (see the table
below).
TV INPUT
TV
TV
PICTURE
NAVI
Number
buttons
VOL +/–
2
Release TV [/1.
TIME/TEXT
◆Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.
CLEAR
AUDIO SUBTITLE
MENU
TOP MENU
RETURN
DISPLAY
Manufacturer Code number
Sony
01 (default)
02
You can control your TV using the buttons
below.
Hitachi
LG/Goldstar/NEC 04
MGA/Mitsubishi 13
By pressing
TV [/1
You can
Turn the TV on or off
Adjust the volume of the TV
Panasonic
Philips
Pioneer
RCA
19
21
16
10
20
18
07
VOL +/–
TV INPUT
(input select)
Switch the TV’s input source
between the TV and other
input sources
b
Samsung
Sharp
Depending on the connected unit, you may not be
able to control your TV using all or some of the
buttons on the supplied remote.
Toshiba
b
• When you replace the batteries of the remote, the
code number you have set may be reset to the
default setting. Set the appropriate code number
again.
• Depending on the connected unit, you may not be
able to control your TV using all or some of the
buttons on the supplied remote.
11US
Step 4: Quick Setup
Follow the steps below to make the minimum number of basic adjustments for using the player.
To skip an adjustment, press >. To return to the previous adjustment, press ..
TV
PICTURE
NAVI
TV
INPUT
TIME/TEXT
CLEAR
AUDIO SUBTITLE
MENU
TOP MENU
ENTER
RETURN
DISPLAY
1
2
Turn on the TV.
5
Press X/x to select a language.
The player displays the menu and
subtitles in the selected language.
Press [/1.
The player turns on.
6
Press ENTER.
The Setup Display for selecting the
aspect ratio of the TV to be connected
appears.
3
Switch the input selector on your
TV so that the signal from the
player appears on the TV screen.
“Press [ENTER] to run QUICK SETUP”
appears at the bottom of the screen. If this
message does not appear, select
“QUICK” under “SETUP” in the Control
SCREEN SETUP
4:3 LETTER BOX
4:3 LETTER BOX
4:3 PAN SCAN
16:9
TV TYPE:
SCREEN SAVER:
BACKGROUND:
BLACK LEVEL:
BLACK LEVEL (COMPONENT OUT):
PROGRESSIVE (COMPONENT OUT ONLY): OFF
OFF
MODE (PROGRESSIVE):
4:3 OUTPUT:
AUTO
FULL
4
Press ENTER without inserting a
disc.
The Setup Display for selecting the
language used in the on-screen display
appears.
7
Press X/xto select the setting that
matches your TV type.
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
LANGUAGE SETUP
OSD:
ENGLISH
ENGLISH
MENU:
AUDIO:
SUBTITLE:
◆ If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
FRENCH
SPANISH
PORTUGUESE
12US
8
9
Press ENTER.
11Press ENTER.
The Setup Display for selecting the type
of jack used to connect your audio
component such as an amplifier
(receiver) appears.
“DTS” is selected.
AUDIO SETUP
AUDIO DRC:
DOWNMIX:
STANDARD
DOLBY SURROUND
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
ON
DOLBY DIGITAL
Is this player connected to an amplifier
(receiver) ? Select the type of jack you
are using.
OFF
OFF
ON
48kHz/96kHz PCM:
YES
AUDIO OUTPUT L/R
DIGITAL OUTPUT
NO
12Press X/x to select whether or
not you wish to send a DTS signal
to your audio component.
Press X/xto select the type of jack
(if any) you are using to connect to
an audio component, then press
ENTER.
If your audio component has a DTS
decoder, select “ON.” Otherwise, select
“OFF.”
If you did not connect an audio
component, select “NO,” then go to step
13.
If you connected an audio component
using just an audio cable, select “YES:
AUDIO OUTPUT L/R,” then go to step
13.
13Press ENTER.
Quick Setup is finished and connections
are complete.
If you connected an audio component
using a digital coaxial cable, select
“YES: DIGITAL OUTPUT.”
10Press X/x to select the type of
Dolby Digital signal you wish to
send to your audio component.
If your audio component has a Dolby
Digital decoder, select “DOLBY
DIGITAL.” Otherwise, select “D-PCM.”
AUDIO SETUP
AUDIO DRC:
DOWNMIX:
STANDARD
DOLBY SURROUND
ON
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
DOLBY DIGITAL
DOLBY DIGITAL
D-PCM
48kHz/96kHz PCM:
13US
To stop playback
Press x.
Playback
To pause playback
Press X.
Playing Discs
z
You can have the player turned off automatically
whenever you leave it in stop mode for more than
30 minutes. To turn this function on or off, set
“AUTO POWER OFF” in “CUSTOM SETUP” to
Depending on the DVD or VIDEO CD, some
operations may be different or restricted.
Refer to the operating instructions supplied
with your disc.
b
Discs created on DVD recorders must be correctly
finalized before they can be played. For more
information about finalizing, refer to the operating
instructions supplied with the DVD recorder.
TV
INPUT
TV
PICTURE
NAVI
Number
buttons
TIME/TEXT
CLEAR
AUDIO SUBTITLE
MENU
Note on playing DTS sound tracks on a
DVD VIDEO
TOP MENU
DTS audio signals are output only through the
DIGITAL OUT (COAXIAL) jack.
ENTER
RETURN
DISPLAY
RETURN
To resume playback from the point where
you stopped the disc (Multi-disc Resume)
When you press N again after you stop
playback, the player starts playback from the
point when you pressed x.
1
2
Press Z on the player, and place
the disc on the disc tray.
z
• To play from the beginning of the disc, press x
twice, then press N.
• With DVD VIDEOs and VIDEO CDs, the player
stores the point where you stopped the disc for up
to 6 discs and resumes playback the next time you
insert the same disc. If you store a resume
playback point for the seventh disc, the resume
playback point for the first disc is deleted.
Playback side
facing down
b
• “MULTI-DISC RESUME” in “CUSTOM
SETUP” must be set to “ON” (default) for this
• Resume Play does not work during Shuffle Play
and Program Play.
• With some discs, Resume Play may not work,
depending on the point you stop playback, or if
you press [/1.
Press N.
The disc tray closes. The player starts
playback (continuous play). Adjust the
volume on the TV or the audio
component.
Depending on the disc, a menu may
appear on the TV screen. For DVD
14US
To play VIDEO CDs With PBC Functions
(PBC Playback)
PBC (Playback Control) allows you to play
VIDEO CDs interactively by following the
menu on the TV screen.
When you start playing a VIDEO CD with
PBC functions, the menu for your selection
appears.
Select an item using the number buttons, and
press ENTER. Then, follow the instructions
in the menu for interactive operations (press
N when “Press SELECT” appears).
Refer to the instructions supplied with the
disc, as the operating procedure may differ
depending on the VIDEO CD.
To return to the menu
Press O RETURN.
z
To play without using PBC, press ./> or the
number buttons while the player is stopped to select
a track, then press N or ENTER.
“Play without PBC” appears on the TV screen and
the player starts continuous play. You cannot play
still pictures such as a menu.
To return to PBC playback, press x twice then
press N.
To lock the disc tray (Child Lock)
You can lock the disc tray to prevent children
from opening it.
When the player is in standby mode, press O
RETURN, ENTER, and [/1 on the remote.
The player turns on and “
” (LOCKED)
appears on the front panel display. The Z
button on the player does not work while the
Child Lock is set.
To unlock the disc tray, press O RETURN,
ENTER, and [/1 again when the player is in
standby mode.
b
Even if you select “RESET” under “SETUP” in the
locked.
15US
,continued
Control Menu display (DISPLAY)
Use the Control Menu to select a function and to view related information. Press DISPLAY
repeatedly to turn on or change the Control Menu display as follows:
, Control Menu display 1
m
Control Menu display 2 (Except CD)
m
Control Menu display off
The Control Menu display 1 and 2 will show different items depending on the disc type.
Example: Control Menu display 1 when playing a DVD VIDEO.
Press X/x to select the Control Menu item, then press ENTER.
2
Currently playing chapter number*
1
Currently playing title number*
1
Total number of titles*
Playback status
(N Playback,
X Pause,
2
Total number of chapters*
x Stop, etc.)
Control Menu items
Type of disc
being played*
3
(
)
)
1 2 2 7
DVD VIDEO
(
1 8 3 4
4
Playing time*
Current setting
T
1 : 3 2 : 5 5
Selected item
OFF
OFF
SET
ON
Options
Function name of
selected Control
Menu item
PROGRAM
ENTER
DISPLAY
Quit:
Operation message
1
* Displays the scene number for VIDEO CDs
(PBC is on), track number for VIDEO CDs/CDs,
album number for DATA discs.
2
* Displays the index number for VIDEO CDs,
MP3 audio track number or JPEG image file
number for DATA discs.
* Displays Super VCD as “SVCD.”
3
4
* Displays the date for JPEG files.
16US
A-B REPEAT (page 21)
Specifies the parts you want to play
repeatedly.
List of Control Menu items
Item
Item Name, Function
TITLE/SCENE/TRACK
CHAPTER/INDEX
SHARPNESS (page 22)
Exaggerates the outline of the image
to produce a sharper picture.
PARENTAL CONTROL
Set to prohibit playback on this
player.
TRACK
Selects the title, scene, track,
chapter, or index to be played.
1
Press X/x to select the search
method.
QUICK:
Use Quick Setup to choose the
desired language of the on-screen
display, the aspect ratio of the TV
and the audio output signal.
“** (**)” is selected (** refers to a
number).
2
Press ENTER.
“** (**)” changes to “-- (**).”
CUSTOM:
3
Press the number buttons to
select the number you want to
search.
In addition to the Quick Setup
setting, you can adjust various other
settings.
4
Press ENTER.
RESET:
Returns the settings in “SETUP” to
the default setting.
TIME/TEXT
Checks the elapsed time and the
remaining playback time.
Input the time code for picture and
music searching (DVD only).
ZOOM
Magnifies the image up to four times
the original size, and scroll using C/
X/x/c.
To return to normal view, press
CLEAR.
1
2
Press ENTER.
Input the time code using the
number buttons, then press
ENTER.
This function is available for all
pictures except a background image.
For example, to find the scene
at 2 hours, 10 minutes, and 20
seconds after the beginning,
just enter “2:10:20.”
ANGLE
Changes the angle.
CUSTOM PICTURE MODE
Adjusts the video signal from the
player. You can select the picture
quality that best suits the program
you are watching.
b
You cannot search for a scene on a
DVD+RW/DVD+R/DVD+R DL
using the time code.
ORIGINAL/PLAY LIST
Selects the type of titles (DVD-VR
mode) to be played, the ORIGINAL
one, or an edited PLAY LIST.
PROGRAM (page 19)
Selects the title, chapter, or track to
play in the order you want.
SHUFFLE (page 20)
Plays the title, chapter, or track in
random order.
REPEAT (page 21)
Plays the entire disc (all titles/all
tracks/all albums) repeatedly or one
title/chapter/track/album repeatedly.
17US
,continued
◆Items for DATA discs
Item Item Name, Function
TVS
Selects surround sound effect when
connecting a stereo TV or 2 front
speakers. This only works when
playing a multichannel Dolby audio
soundtrack. Furthermore, if the
player is set up to output the signal
from the DIGITAL OUT
(COAXIAL) jack, the surround
effect will only be heard when
“DOLBY DIGITAL” is set to
“D-PCM” in “AUDIO SETUP”
ALBUM
Selects the album that contains MP3
audio tracks and JPEG image file to
be played.
FILE
Selects the JPEG image file to be
played.
DATE
Displays the date the picture was
taken by a digital camera.
The default setting is underlined.
• OFF
Cancels the setting.
Specifies the duration for which the
slides are displayed on the screen.
• TVS DYNAMIC THEATER
• TVS DYNAMIC
• TVS WIDE
This mode is effective when the
distance between the front L and R
speakers is short, such as with built-
in speakers on a stereo TV.
Selects the effects to be used for
changing slides during a slide show.
MODE (MP3, JPEG)
Selects the data type; MP3 audio
track (AUDIO), JPEG image file
(IMAGE), or both (AUTO) to be
played when playing a DATA disc.
• TVS NIGHT
This feature is useful when you want
to hear the dialog and enjoy the
surround sound effects of “TVS
WIDE” at low volume.
• TVS STANDARD
Use this setting when you want to
use TVS with 2 separate speakers.
b
• When you select one of the TVS
modes, turn off the surround setting
of the connected TV or audio
component.
• The TVS effects do not work when
using the Fast Play or Slow Play
functions, even though you can
change the TVS modes.
z
The Control Menu icon indicator lights up in green
t
when you select any item
except “OFF” (“PROGRAM,” “SHUFFLE,”
“REPEAT,” “A-B REPEAT,” “SHARPNESS,”
“ZOOM,” “TVS” only). The “ORIGINAL/PLAY
LIST” indicator lights up in green when you select
“PLAY LIST” (default setting). The “ANGLE”
indicator lights up in green when you can change
the angle. The “CUSTOM PICTURE MODE”
indicator lights up in green when any setting other
than “STANDARD” is selected.
18US
3 Select the title, chapter, or track you
want to program.
Various Play Mode
Functions
◆ When playing a DVD VIDEO
For example, select chapter “03” of title
“02.”
You can set the following play modes:
Press X/x to select “02” under “T,” then
press ENTER.
PROGRAM
T
C
ALL CLEAR
– –
– –
ALL
1. TITLE
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
– –
– –
– –
– –
– –
– –
01
02
03
04
05
06
01
02
03
04
05
b
The play mode is canceled when:
– you open the disc tray.
– you press [/1 and the player enters standby mode.
Creating your own
program (Program Play)
Next, press X/x to select “03” under “C,”
then press ENTER.
PROGRAM
T
ALL CLEAR
1. TITLE 0 2 0 3
You can play the contents of a disc in the
order you want. You can program up to 99
titles, chapters, and tracks.
–
– –
– –
– –
– –
– –
– –
– –
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
01
02
03
04
05
1 After selecting
(PROGRAM)
X/x to select “SET t,” then press
ENTER.
Selected title and chapter
“TRACK” is displayed when you play
a VIDEO CD or CD.
◆ When playing a VIDEO CD or CD
For example, select track “02.”
Press X/x to select “02” under “T,” then
press ENTER.
PROGRAM
T
ALL CLEAR
– –
1. TITLE
2. TITLE
3. TITLE
4. TITLE
– –
– –
– –
– –
– –
– –
Selected track
01
02
03
04
05
0:15:30
T
PROGRAM
5. TITLE
6. TITLE
7. TITLE
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
– –
0 2
– –
– –
– –
– –
– –
– –
01
02
03
04
05
Titles or tracks recorded on a disc
2 Press c.
The cursor moves to the title or track row
“T” (in this case, “01”).
Total time of the programmed tracks
PROGRAM
4 Repeat steps 2 to 3, to program other
titles, chapters, or tracks.
T
C
ALL CLEAR
1. TITLE
– –
– –
01
02
03
04
05
ALL
– –
– –
– –
– –
– –
– –
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
01
02
03
04
05
06
The programmed titles, chapters, and
tracks are displayed in the selected order.
Chapters recorded on a disc
19US
,continued
5 Press N.
Playing in random order
(Shuffle Play)
You can have the player “shuffle” titles,
chapters, or tracks. Subsequent “shuffling”
may produce a different playing order.
Program Play begins.
When the program ends, you can restart
the same program again by pressing N.
To return to normal play
Press CLEAR, or select “OFF” in step 1. To
play the same program again, select “ON” in
step 1 and press ENTER.
1 After selecting
(SHUFFLE) on
x to select the item to be shuffled.
◆ When playing a DVD VIDEO
• TITLE
• CHAPTER
To change or cancel a program
1
Follow step 1 of “Creating your own
◆ When playing a VIDEO CD or CD
• TRACK
2
Select the program number of the title,
chapter, or track you want to change or
cancel using X/x and press c. If you
want to delete the title, chapter, or track
from the program, press CLEAR.
◆ When Program Play is activated
• ON: shuffles titles, chapters, or tracks
selected in Program Play.
2 Press ENTER.
3
Follow step 3 of “Creating your own
program (Program Play)” for new
programming. To cancel a program,
select “--” under “T,” then press ENTER.
Shuffle Play starts.
To return to normal play
Press CLEAR, or select “OFF” in step 1.
To cancel all of the titles, chapters, or
tracks in the programmed order
Press X and select “ALL CLEAR” in step 2 of
“Creating your own program (Program
Play)” and press ENTER.
z
• You can set Shuffle Play while the player is
stopped. After selecting the “SHUFFLE” option,
press N. Shuffle Play starts.
• Up to 200 chapters in a disc can be played in
random order when “CHAPTER” is selected.
z
You can perform Repeat Play or Shuffle Play of
programmed titles, chapters, or tracks. During
Program Play, follow the steps of Repeat Play
b
You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
b
• When you program tracks on a Super VCD, the
total playing time is not displayed.
• You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
20US
Playing repeatedly
(Repeat Play)
Repeating a specific
portion (A-B Repeat Play)
You can play all of the titles or tracks on a
disc, or a single title, chapter, or track
repeatedly.
You can use a combination of Shuffle or
Program Play modes.
You can play a specific portion of a title,
chapter or track repeatedly.
1 After selecting
(A-B REPEAT)
X/x to select “SET t,” then press
ENTER.
1 After selecting
(REPEAT) on
x to select the item to be repeated.
• DISC: repeats all of the titles, tracks, or
albums. (Select ORIGINAL or PLAY
LIST in DVD-VR mode.)
The “A-B REPEAT” setting bar appears.
A 18 - 1:32:30
B
• TITLE: repeats the current title on a
disc.
• CHAPTER: repeats the current chapter.
• TRACK: repeats the current track.
• ALBUM: repeats the current album.
2 During playback, when you find the
starting point (point A) of the portion to
be played repeatedly, press ENTER.
The starting point (point A) is set.
◆ When Program Play or Shuffle Play is
activated
• ON: repeats Program Play or Shuffle
Play.
A 18 - 1:32:55 B 18 - 1:33:05
2 Press ENTER.
Repeat Play starts.
3 When you reach the ending point
(point B), press ENTER again.
The set points are displayed and the
player starts repeating this specific
portion.
To return to normal play
Press CLEAR, or select “OFF” in step 1.
b
You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
To return to normal play
Press CLEAR, or select “OFF” in step 1.
b
• A-B Repeat Play does not work across multiple
titles.
• You may not set A-B Repeat Play for contents in
DVD-VR mode that contains still pictures.
21US
b
The “BRIGHTNESS” setting is not effective if you
connect the player via the VIDEO OUT jack and
select “PROGRESSIVE (COMPONENT OUT
ONLY)” to “ON” using the “SCREEN SETUP.”
Customizing the
Playback Configuration
Sharpening the picture
(SHARPNESS)
Adjusting the playback
picture (CUSTOM PICTURE MODE)
You can enhance the outlines of images to
produce a sharper picture.
You can adjust the video signal from the
player to obtain the picture quality you want.
1 After selecting
(SHARPNESS)
X/x to select a level.
1 After selecting
(CUSTOM
PICTURE MODE) on the Control Menu
setting you want.
The default setting is underlined.
• OFF: cancels this option.
• 1: enhances the outline.
The default setting is underlined.
• STANDARD: displays a standard
picture.
• DYNAMIC 1: produces a bold
dynamic picture by increasing the
picture contrast and the color intensity.
• DYNAMIC 2: produces a more
dynamic picture than DYNAMIC 1 by
further increasing the picture contrast
and color intensity.
• CINEMA 1: enhances details in dark
areas by increasing the black level.
• CINEMA 2: white colors become
brighter and black colors become
richer, and the color contrast is
increased.
• 2: enhances the outline more than 1.
2 Press ENTER.
The selected setting takes effect.
Locking discs (PARENTAL
CONTROL)
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. The
“PARENTAL CONTROL” function allows
you to set a playback limitation level.
1 After selecting
(PARENTAL
CONTROL) on the Control Menu
“PLAYER t,” then press ENTER.
The password is required.
• MEMORY: adjusts the picture in
greater detail.
PICTURE
Changes the contrast.
BRIGHTNESS Changes the overall
brightness.
2 Enter or re-enter your 4-digit password
using the number buttons, then press
ENTER.
COLOR
HUE
Makes the colors
deeper or lighter.
Changes the color
balance.
The display for setting the playback
limitation level appears.
3 Press X/x to select “STANDARD,”
2 Press ENTER.
then press ENTER.
The selected setting takes effect.
The selection items for “STANDARD”
are displayed.
z
When you watch a movie, “CINEMA 1” or
“CINEMA 2” is recommended.
22US
4 Press X/x to select a geographic area
as the playback limitation level, then
press ENTER.
Playing MP3 Audio and
JPEG Images
The area is selected.
When you select “OTHERS t,” select
and enter a standard code in the table on
page 37 using the number buttons.
You can play MP3 audio tracks and JPEG
image files on DATA discs.
You can enjoy JPEG images as a slide show.
5 Press X/x to select “LEVEL,” then
press ENTER.
PICTURE
TV
TV
PICTURE
NAVI
INPUT
NAVI
The selection items for “LEVEL” are
displayed.
TIME/TEXT
6 Select the level you want using X/x,
TIME/TEXT
SUBTITLE
MENU
CLEAR
AUDIO SUBTITLE
MENU
then press ENTER.
CLEAR
TOP MENU
Parental Control setting is complete.
The lower the value, the stricter the
limitation.
ENTER
RETURN
DISPLAY
RETURN
DISPLAY
To turn off the Parental Control function
Set “LEVEL” to “OFF” in step 6.
To set or change your password
After selecting “PARENTAL CONTROL”
on the Control Menu, select “PASSWORD
t,” then press ENTER.
z
You can view the disc information while playing
MP3 audio tracks and JPEG image files using
z
If you forget your password, remove the disc and
repeat step 1 of “Locking discs (PARENTAL
CONTROL).” When you are asked to enter your
password, enter “199703” using the number
buttons, then press ENTER. The display will ask
you to enter a new 4-digit password. After you enter
a new 4-digit password, replace the disc in the
player and press N. When the display for entering
your password appears, enter your new password.
b
DATA CDs recorded in KODAK Picture CD
format automatically start playing when inserted.
1
Press MENU.
The list of albums on the disc appears.
When an album is being played, its title is
shaded.
b
Depending on the disc, you may be asked to change
the parental control level while playing the disc. In
this case, enter your password, then change the
level. If the Resume Play mode is canceled, the
level returns to the previous level.
1
( 15)
Album 1
Album 2
Album 3
Album 4
Album 5
Album 6
Album 7
Album 8
2
Press X/x to select the album.
23US
,continued
3
Press N.
Playback starts from the selected album.
The JPEG images in the selected album
start playing as a slide show.
Selecting a JPEG image file
1 Press MENU.
The list of albums on the disc appears.
To select a specific MP3 audio track,
press ENTER and press X/x to select a
track, then press ENTER.
To select a specific JPEG image file, see
2 Press X/x to select the album, then
press PICTURE NAVI.
The image files in the album appear in 16
subscreens. A scroll box is displayed on
the right.
To stop playback
Press x.
1
2
3
4
5
6
7
8
To go to the next or previous page
Press c or C.
9
10
14
11
15
12
16
To return to the previous display
Press O RETURN.
13
To display additional images, select a
bottom image and press x. To return to a
previous image, select a top image and
press X.
To go to the next or previous MP3 audio
track
Press > or . during playback. You can
select the first track of the next album by
pressing > during playback of the last
track of the current album.
Note that you cannot return to the previous
album by using ., and that you need to
select the previous album from the album list.
3 PressC/X/x/cto select the image you
want to view, and press ENTER.
The selected image appears.
To go to the next or previous JPEG image
file
Press C or c during playback. You can select
the first file of the next album by pressing c
during playback of the last file of the current
album.
Note that you cannot return to the previous
album by using C, and that you need to select
the previous album from the album list.
To turn on or off the display
Press MENU repeatedly.
z
Of the selected album, you can select to play only
the MP3 audio tracks, JPEG image files, or both, by
To rotate a JPEG image
Press X/x while viewing the image. Each
time you press X, the image rotates
counterclockwise by 90 degrees.
To return to normal view, press CLEAR.
Note that the view also returns to normal if
you press C/c to go to the next or previous
image.
24US
To display JPEG image information
Press SUBTITLE while viewing JPEG image
files.
The file name, camera maker/model, date,
time, picture resolution, file size, camera
setting information (ISO speed rating,
Exposure time, F Number, Exposure bias, or
Focal length) of the picture are displayed on
the screen.
Setting the pace for a
slide show (INTERVAL)
You can set the time the slides are displayed
on the screen.
1 After selecting
(INTERVAL) on
x to select a setting.
is displayed when the picture was taken
using flash.
The default setting is underlined.
• NORMAL: sets to standard duration.
• FAST: sets a duration shorter than
NORMAL.
is displayed when the image is
automatically rotated.
To hide the information, press SUBTITLE.
Note that the above information may not
appear depending on the digital camera.
• SLOW 1: sets a duration longer than
NORMAL.
• SLOW 2: sets a duration longer than
SLOW 1.
To stop viewing the JPEG image
Press x.
2 Press ENTER.
b
Selecting the slides’
appearance (EFFECT)
PICTURE NAVI does not work if “AUDIO (MP3)”
You can select the way the slides are
displayed during a slide show.
1 After selecting
(EFFECT) on
x to select a setting.
The default setting is underlined.
• MODE 1: the images randomly cycle
through the effects.
• MODE 2: the next image slides over the
previous image.
• MODE 3: the image sweeps in from top
to bottom.
• MODE 4: the image sweeps in from left
to right.
• MODE 5: the image stretches out from
the center of the screen.
• OFF: turns off this function.
2 Press ENTER.
25US
LANGUAGE SETUP
Settings and Adjustments
“LANGUAGE SETUP” allows you to set
various languages for the on-screen display or
sound track.
Using the Setup Display
By using the Setup Display, you can make
various adjustments to items such as picture
and sound. You can also set a language for the
subtitles and the Setup Display, among other
things.
Select “LANGUAGE SETUP” in the Setup
Display.
◆OSD (On-Screen Display)
Switches the display language on the screen.
For details on each Setup Display item, see
◆MENU (DVD VIDEO only)
You can select the desired language for the
disc’s menu.
b
Playback settings stored in the disc take priority
over the Setup Display settings and not all of the
functions described may work.
◆AUDIO (DVD VIDEO only)
Switches the language of the sound track.
When you select “ORIGINAL,” the language
given priority in the disc is selected.
1
2
Press DISPLAY when the player is
in stop mode.
◆SUBTITLE (DVD VIDEO only)
Switches the language of the subtitle recorded
on the DVD VIDEO.
When you select “AUDIO FOLLOW,” the
language for the subtitles changes according
to the language you selected for the sound
track.
The Control Menu appears.
Press X/x to select
(SETUP), then press ENTER.
The options for “SETUP” appear.
• QUICK: makes the basic adjustments
(page 12).
z
If you select “OTHERS t” in “MENU,”
“SUBTITLE,” or “AUDIO,” select and enter a
language code from “Language Code List” on
page 37 using the number buttons.
• CUSTOM: makes various adjustments.
• RESET: resets all the settings explained
3
Press X/x to select “CUSTOM,”
then press ENTER.
The Setup Display appears.
Select the setup category and adjust each
item following the instruction on pages
b
If you select a language in “MENU,”
“SUBTITLE,” or “AUDIO” that is not recorded on
a DVD VIDEO, one of the recorded languages will
be automatically selected.
LANGUAGE SETUP
OSD:
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
MENU:
AUDIO:
SUBTITLE:
26US
◆ SCREEN SAVER
The screen saver image appears when you
leave the player in pause or stop mode for 15
minutes, or when you play a CD, or DATA
disc (MP3 audio) for more than 15 minutes.
The screen saver will help prevent your
display device from becoming damaged
(ghosting). Press N to turn off the screen
saver.
SCREEN SETUP
Choose settings according to the TV to be
connected.
Select “SCREEN SETUP” in the Setup
Display. To use the display, see “Using the
The default settings are underlined.
ON
Turns on the screen saver.
Turns off the screen saver.
OFF
◆ TV TYPE
Selects the aspect ratio of the connected TV
(4:3 standard or wide).
◆ BACKGROUND
Selects the background color or picture on the
TV screen when the player is in stop mode or
while playing a CD, or DATA disc (MP3
audio).
4:3
LETTER
BOX
Select this when you connect a
4:3 screen TV. Displays a wide
picture with bands on the upper
and lower portions of the
screen.
JACKET
PICTURE
The jacket picture (still picture)
appears, but only when the
jacket picture is already
4:3
Select this when you connect a
PAN SCAN 4:3 screen TV. Automatically
displays the wide picture on the
entire screen and cuts off the
recorded on the disc (CD-
EXTRA, etc.). If the disc does
not contain a jacket picture, the
“GRAPHICS” picture appears.
portions that do not fit.
16:9
Select this when you connect a
wide-screen TV or a TV with a
wide mode function.
GRAPHICS A preset picture stored in the
player appears.
BLUE
The background color is blue.
The background color is black.
BLACK
4:3 LETTER BOX
◆ BLACK LEVEL
Selects the black level (setup level) for the
video signals output from the jacks other than
COMPONENT VIDEO OUT.
4:3 PAN SCAN
ON
Sets the black level of the
output signal to the standard
level.
16:9
OFF
Lowers the standard black
level. Use this when the picture
becomes too white.
b
Depending on the DVD, “4:3 LETTER BOX” may
be selected automatically instead of “4:3 PAN
SCAN” or vice versa.
27US
,continued
◆ BLACK LEVEL (COMPONENT OUT)
Selects the black level (setup level) for the
video signals output from the COMPONENT
VIDEO OUT jacks. You cannot select this
when the player outputs progressive signals
(page 9).
◆MODE (PROGRESSIVE)
In order for these images to appear natural on
your screen when output in progressive
mode, the progressive video signal needs to
be converted to match the type of DVD
software that you are watching.
This setting is effective only when you set
“PROGRESSIVE (COMPONENT OUT
ONLY)” in “SCREEN SETUP” to “ON.”
OFF
Sets the black level of the
output signal to the standard
level. Normally select this
position.
AUTO
Automatically detects the
software type (film-based or
video-based) and selects the
appropriate conversion mode.
Normally, select this position.
ON
Raises the standard black level.
Use this setting when the
picture appears too dark.
VIDEO
Fixes the conversion mode to
the mode for video-based
software.
◆ PROGRESSIVE (COMPONENT OUT
ONLY)
If your TV accepts progressive (480p) format
signals, set “PROGRESSIVE
◆4:3 OUTPUT
This setting is effective only when you set
“TV TYPE” in “SCREEN SETUP” to
“16:9.”
(COMPONENT OUT ONLY)” to “ON.”
Note that you must connect to a progressive
format TV using the COMPONENT VIDEO
Adjust this to watch 4:3 aspect ratio
progressive signals. If you can change the
aspect ratio on your progressive format
(480p) compatible TV, change the setting on
your TV, not the player. This setting is
effective only when “PROGRESSIVE
(COMPONENT OUT ONLY)” is set to
“ON” in “SCREEN SETUP.”
OFF
ON
To output normal (interlace)
signals.
To output progressive signals.
To output progressive signals
1
Select “PROGRESSIVE
(COMPONENT OUT ONLY),” and
press ENTER.
FULL
Select this when you can
change the aspect ratio on your
TV.
2
3
Select “ON,” and press ENTER.
The display asks for confirmation.
NORMAL
Select this when you cannot
change the aspect ratio on your
TV. Shows a 16:9 aspect ratio
signal with black bands on left
and right sides of the image.
Select “Start,” and press ENTER.
The video switches to a progressive
signal for 5 seconds.
4
If the picture appears normal, select
“YES,” and press ENTER.
If not, select “NO,” and press ENTER.
To reset the setting
16:9 aspect ratio TV
If the picture does not appear normal or goes
blank, press [/1 to turn off the player, and
enter “369” using the number buttons on the
remote, then press [/1 to turn on the player
again.
28US
b
• When you set the item to “AUTO,” the language
may change. The “TRACK SELECTION” setting
has higher priority than the “AUDIO” settings in
“LANGUAGE SETUP” (page 26).
sound track is not played even if you set “TRACK
SELECTION” to “AUTO.”
• If PCM, DTS, and Dolby Digital sound tracks
have the same number of channels, the player
selects PCM, DTS, and Dolby Digital sound
tracks in this order.
CUSTOM SETUP
Use this to set up playback related and other
settings.
Select “CUSTOM SETUP” in the Setup
Display. To use the display, see “Using the
The default settings are underlined.
◆ AUTO POWER OFF
◆ MULTI-DISC RESUME (DVD VIDEO/
VIDEO CD only)
Switches the Multi-disc Resume setting on or
off. Resume playback can be stored in
memory for up to 6 different DVD VIDEOs/
Switches the Auto Power Off setting on or
off.
OFF
ON
Switches this function off.
The player enters standby mode
when left in stop mode for more
than 30 minutes.
ON
Stores the resume setting in
memory for up to 6 discs.
OFF
Does not store the resume
◆ AUTO PLAY
setting in memory. Playback
restarts at the resume point only
for the current disc in the player.
Switches the Auto Play setting on or off. This
function is useful when the player is
connected to a timer (not supplied).
OFF
ON
Switches this function off.
b
If you run Quick Setup, Multi-disc Resume setting
stored in memory may return to the default settings.
Automatically starts playback
when the player is turned on by
a timer (not supplied).
◆ PAUSE MODE (DVDs only)
Selects the picture in pause mode.
AUTO
The picture, including subjects
that move dynamically, is
output with no jitter. Normally
select this position.
FRAME
The picture, including subjects
that do not move dynamically,
is output in high resolution.
◆ TRACK SELECTION (DVD VIDEO only)
Gives the sound track which contains the
highest number of channels priority when you
play a DVD VIDEO on which multiple audio
formats (PCM, DTS, or Dolby Digital
format) are recorded.
OFF
No priority given.
Priority given.
AUTO
29US
◆DIGITAL OUT
Selects if audio signals are output via the
DIGITAL OUT (COAXIAL) jack.
AUDIO SETUP
ON
Normally, select this position.
When you select “ON,” see
for further settings.
“AUDIO SETUP” allows you to set the sound
according to the playback and connection
conditions.
OFF
The influence of the digital
circuit upon the analog circuit is
minimal.
Select “AUDIO SETUP” in the Setup
Display. To use the display, see “Using the
The default settings are underlined.
Setting the digital output signal
◆ AUDIO DRC (Dynamic Range Control)
(DVDs only)
Makes the sound clear when the volume is
turned down when playing a DVD that
conforms to “AUDIO DRC.”
This function affects the output from the
following jacks:
Switches the method of outputting audio
signals when you connect a component such
as an audio component or MD deck with a
digital input jack.
Select “DOLBY DIGITAL,” “DTS,” and
“48kHz/96kHz PCM” after setting
“DIGITAL OUT” to “ON.”
If you connect a component that is
incompatible with the selected audio signal, a
loud noise (or no sound) may be heard from
the speakers, risking damage to your ears or
speakers.
– AUDIO OUT L/R jacks
– DIGITAL OUT (COAXIAL) jack only
when “DOLBY DIGITAL” is set to “D-
STANDARD Normally, select this position.
TV MODE
Makes low sounds clear even if
you turn the volume down.
◆DOLBY DIGITAL (DVDs only)
Selects the type of Dolby Digital signal.
WIDE
RANGE
Gives you the feeling of being
at a live performance.
DOLBY
DIGITAL
Select this when the player is
connected to an audio
◆ DOWNMIX (DVDs only)
Switches the method for mixing down to 2
channels when you play a DVD which has
rear sound elements (channels) or is recorded
in Dolby Digital format. For details on the
function affects the output of the following
jacks:
component with a built-in
Dolby Digital decoder.
D-PCM
Select this when the player is
connected to an audio
component without a built-in
Dolby Digitaldecoder. You can
select whether the signals
conform to Dolby Surround
(Pro Logic) or not by making
adjustments to the
– AUDIO OUT L/R jacks
– DIGITAL OUT (COAXIAL) jack when
“DOLBY DIGITAL” is set to “D-PCM”
(page 30).
“DOWNMIX” item in
DOLBY
SUR-
ROUND
Normally, select this position.
Multi-channel audio signals are
output to 2 channels for enjoying
surround sounds.
NORMAL Multi-channel audio signals are
downmixed to 2 channels for use
with your stereo.
30US
◆ DTS
Selects whether or not to output DTS signals.
OFF
Select this when the player is
connected to an audio
component without a built-in
DTS decoder.
ON
Select this when the player is
connected to an audio
component with a built-in DTS
decoder.
• When you play a DVD VIDEO with DTS
sound tracks, set “DTS” to “ON” in
• If you connect the player to audio
equipment without a DTS decoder, do not
set “DTS” to “ON” in “AUDIO SETUP”
the speakers, affecting your ears or causing
the speakers to be damaged.
◆ 48kHz/96kHz PCM (DVD VIDEO only)
Selects the sampling frequency of the audio
signal.
48kHz/16bit The audio signals of DVD
VIDEOs are always converted
to 48kHz/16bit.
96kHz/24bit All types of signals including
96kHz/24bit are output in their
original format. However, if the
signal is encrypted for
copyright protection purposes,
the signal is only output as
48kHz/16bit.
b
The analog audio signals from the AUDIO OUT
L/R jacks are not affected by this setting and keep
their original sampling frequency level.
31US
Sound
Additional Information
There is no sound.
, Re-connect the connecting cable securely.
, The connecting cable is damaged.
, The player is connected to the wrong input
, The audio component input is not correctly
set.
, The player is in pause mode or in Slow-
motion Play mode.
, The player is in fast forward or fast reverse
mode.
Troubleshooting
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
, If the audio signal does not come through
the DIGITAL OUT (COAXIAL) jack,
, While playing a Super VCD on which the
audio track 2 is not recorded, no sound will
come out when you select “2:STEREO,”
“2:1/L,” or “2:2/R.” Press AUDIO to select
the recorded track.
Power
The power is not turned on.
, Check that the power cord is connected
securely.
Picture
There is no picture/picture noise appears.
, Re-connect the connecting cable securely.
, The connecting cables are damaged.
and switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“AUDIO DRC” in “AUDIO SETUP” to
Operation
, The disc is dirty or flawed.
, You set the “PROGRESSIVE
(COMPONENT OUT ONLY)” to “ON” in
your TV cannot accept the progressive
the setting.
The remote does not function.
, The batteries in the remote are weak.
, There are obstacles between the remote and
the player.
, The distance between the remote and the
player is too far.
, Even if your TV is compatible with
progressive format 480p signals and
connected using COMPONENT VIDEO
OUT jacks, the image may be affected when
you set the player to progressive format. In
this case, set the “PROGRESSIVE
(COMPONENT OUT ONLY)” in
that the player is set to normal (interlace)
format.
, The remote is not pointed at the remote
sensor on the player.
The disc does not play.
, The disc is turned over.
Insert the disc with the playback side facing
down.
, The disc is skewed.
, The player cannot play certain discs
(page 34).
, The region code on the DVD does not match
the player.
, Moisture has condensed inside the player
, The player cannot play a recorded disc that
is not correctly finalized (page 35).
32US
The MP3 audio track cannot be played
(page 34).
, The player cannot play audio tracks in
mp3PRO format.
, “MODE (MP3, JPEG)” is set to “IMAGE
Some functions such as Stop, Fast Play,
Slow Play, Slow-motion Play, Repeat
Play, Shuffle Play, or Program Play cannot
be performed.
, Depending on the disc, you may not be able
to do some of the operations above.
The JPEG image file cannot be played
(page 34).
The player does not operate properly.
, When static electricity, etc., causes the
player to operate abnormally, unplug the
player.
, The image is larger than 3072 (width) ×
2048 (height) in normal mode, or more than
3,300,000 pixels in progressive JPEG.
(Some progressive JPEG files cannot be
displayed even if the file size is within this
specified capacity.)
5 numbers or letters are displayed on the
screen.
, The self-diagnosis function was activated.
, “MODE (MP3, JPEG)” is set to “AUDIO
The disc tray does not open and “
(LOCKED) appears on the front panel
display.
”
The MP3 audio tracks and JPEG image
files start playing simultaneously.
, “MODE (MP3, JPEG)” is set to “AUTO”
The album/track/file names are not
displayed correctly.
, The player can only display numbers and
alphabet. Other characters are displayed as
The disc tray does not open and
“
” (TRAY LOCKED) appears on
the front panel display.
, Contact your Sony dealer or local
authorized Sony service facility.
“ .”
*
The disc does not start playing from the
“Data error” appears on the TV screen
when playing a DATA disc.
, The MP3 audio track/JPEG image file you
want to play is broken.
, The data is not MPEG-1 Audio Layer III
data.
, The JPEG image file format does not
beginning.
, Program Play, Shuffle Play, Repeat Play, or
“Copyright lock” appears and the screen
turns blue when playing in DVD-VR mode.
, Images taken from digital broadcasts, etc.,
may contain copy protection signals, such
as complete copy protection signals, single
copy signals, and restriction-free signals.
When images that contain copy protection
signals are played, a blue screen may appear
instead of the images. It may take a while
when looking for playable images. (For
player that cannot play images that contain
a copy protection only)
, The JPEG image file has the extension
“.JPG” or “.JPEG,” but is not in JPEG
format.
33US
The player can play recordable media that is
correctly finalized.
“DVD+RW,” “DVD-RW,” “DVD+R,”
“DVD+R DL,” “DVD-R,” “DVD VIDEO,”
and “CD” logos are trademarks.
Self-diagnosis Function
(When letters/numbers appear on the
screen)
The player cannot play the discs other than
above. Also, the player cannot play the
following discs:
• A disc recorded in a color system other than
NTSC, such as PAL or SECAM (this player
conforms to the NTSC color system).
• A disc that has a non-standard shape (e.g.,
card, heart).
When the self-diagnosis function is activated
to prevent the player from malfunctioning, a
five-character service number (e.g., C 13 50)
with a combination of a letter and four digits
appears on the screen. In this case, check the
following table.
First three
characters of action
the service
Cause and/or corrective
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane
tape or a sticker still left on it.
number
C 13
The disc is dirty or recorded
Note about CDs/DVDs
The player can play CD-ROMs/CD-Rs/CD-
RWs recorded in the following formats:
– music CD format
in a format that this player
,Clean the disc with a
cleaning cloth or check its
format.
– video CD format
– MP3 audio tracks and JPEG image files of
format conforming to ISO 9660* Level 1/
Level 2, or its extended format, Joliet
– KODAK Picture CD format
C 31
The disc is not inserted
correctly.
,Re-insert the disc
correctly.
* A logical format of files and folders on CD-
ROMs, defined by ISO (International
Organization for Standardization).
Playable Discs
The player can play DVD-ROMs/
DVD+RWs/DVD+Rs/DVD+R DLs/
DVD-RWs/DVD-Rs/DVD-R DLs recorded
in the following formats:
Format of discs
Commercial DVD
– MP3 audio tracks and JPEG image files of
format conforming to UDF (Universal Disk
Format).
DVD-RW/-R
MP3 audio track or JPEG image
file that the player can play
DVD+RW/+R/
+R DL
The player can play the following tracks and
files:
– MP3 audio tracks with the extension
“.MP3.”
– JPEG image files with the extension
“.JPEG” or “.JPG.”
– JPEG image files that conform to the DCF*
image file format.
VIDEO CD/
Music CD
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by JEITA
(Japan Electronics and Information Technology
Industries Association).
CD-RW/-R
34US
z
Region code
• If you add numbers (01, 02, 03, etc.) to the front
of the track/file names when you store the tracks
(or files) in a disc, the tracks and files will be
played in that order.
• Since a disc with a complex hierarchy of folders
takes longer to start playback, it is recommended
that you create albums with no more than two
hierarchies.
Your player has a region code printed at the
bottom of the unit and only will play
commercial DVDs (playback only) labeled
with identical region codes. This system is
used to protect copyrights.
• To repeat both MP3 audio tracks and JPEG image
files in a single album, repeat the same MP3 audio
track or album when “MODE (MP3, JPEG)” is set
to “AUTO.” See “Playing repeatedly (Repeat
ALL
Commercial DVDs labeled
play on this player.
will also
Depending on the commercial DVD, there
may be no region code indication, even
though playing the commercial DVD is
prohibited by area restrictions.
b
• The player will play any data with the extension
“.MP3,” “.JPG,” or “.JPEG,” even if they are not
in MP3 or JPEG format. Playing these data may
generate a loud noise which could damage your
speaker system.
DVP–XXXX
X
Region code
00V 00Hz
NO.
00W
0-000-000-00
• The player does not conform to audio tracks in
mp3PRO format.
• Some JPEG files cannot be played.
b
• Notes about recordable media
• You can view a slide show with sound only when
the MP3 audio tracks and JPEG image files are
placed in the same album.
• If playing time of JPEG image or MP3 audio is
longer than the other, the longer one continues
without sound or image.
Some recordable media cannot be played on this
player due to the recording quality or physical
condition of the disc, or the characteristics of the
recording device and authoring software.
The disc will not play if it has not been correctly
finalized. For more information, refer to the
operating instructions for the recording device.
Note that some playback functions may not work
with some DVD+RWs/DVD+Rs/DVD+R DLs,
even if they have been correctly finalized. In this
case, view the disc by normal playback. Also
some DATA discs created in Packet Write format
cannot be played.
• If you play large MP3 track data and JPEG image
data at the same time, the sound may skip. It is
recommended that you set the MP3 bit rate to 128
kbps or lower when creating the file. If the sound
still skips, then reduce the size of the JPEG file.
• Some JPEG files, especially progressive JPEG
files or JPEG files of 3,000,000 pixels or more,
may take longer to display than others, which may
make the duration seem longer than the setting
you selected.
• The player recognizes a maximum of 200 albums
regardless of the selected mode. Of each album,
the player recognizes up to 300 MP3 audio tracks
and 300 JPEG image files when “AUTO” is
selected, 600 MP3 audio tracks when “AUDIO
(MP3)” is selected and 600 JPEG image files
when “IMAGE (JPEG)” is selected.
• Music discs encoded with copyright protection
technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Various music discs encoded with copyright
protection technologies are marketed by some
record companies. Please be aware that among
those discs, there are some that do not conform to
the CD standard and may not be playable by this
product.
• Proceeding to the next or another album may take
some time.
• For player that cannot play images that
contain a copy protection only
Images in DVD-VR mode with CPRM*
protection may not be played if they contain a
copy protection signal. “Copyright lock” appears
on the screen.
* CPRM (Content Protection for Recordable
Media) is a coding technology that protects the
copyright of images.
35US
,continued
• Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
Specifications
System
Laser: Semiconductor laser
Outputs
Note on playback operations of
DVDs and VIDEO CDs
(Jack name: Jack type/Output level/Load
impedance)
AUDIO OUT:
Some playback operations of DVDs and
VIDEO CDs may be intentionally set by
software producers. Since this player plays
DVDs and VIDEO CDs according to the disc
contents the software producers designed,
some playback features may not be available.
Also, refer to the instructions supplied with
the DVDs or VIDEO CDs.
Phono jack/2 Vrms/10 kilohms
DIGITAL OUT (COAXIAL):
Phono jack/0.5 Vp-p/75 ohms
COMPONENT VIDEO OUT(Y, PB, PR):
Phono jack/Y: 1.0 Vp-p/PB, PR
:
1
interlace* = 0.648 Vp-p,
2
progressive or interlace* = 0.7 Vp-p/75
ohms
1
2
*
*
BLACK LEVEL (COMPONENT OUT) is ON
BLACK LEVEL (COMPONENT OUT) is OFF
Copyrights
VIDEO OUT:
Phono jack/1.0 Vp-p/75 ohms
This product incorporates copyright
protection technology that is protected by
U.S. patents and other intellectual property
rights. Use of this copyright protection
technology must be authorized by
Macrovision, and is intended for home and
other limited viewing uses only unless
otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
General
Power requirements:
U.S. models: 120 V AC, 60 Hz
Models for other areas: 110-240 V AC,
50/60 Hz
Power consumption: 10 W
Dimensions (approx.):
320 × 32 × 209 mm (12 5/8 × 1 5/6
×
8 1/4 in.) (width/height/depth) incl.
projecting parts
Mass (approx.): 1.2 kg (2 lb 11 oz)
Operating temperature: 5 °C to 35 °C
(41 °F to 95 °F)
Operating humidity: 25 % to 80 %
Supplied accessories
• Audio/video cable (phono plug × 3 y
phono plug × 3) (1)
• Remote commander (remote) (1)
• Size AA (R6) batteries (2)
A plug adaptor is included with some models.
Specifications and design are subject to
change without notice.
36US
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027 Afar
1183 Irish
1347 Maori
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1186 Scots Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1358 Maltese
1363 Burmese
1365 Nauru
1369 Nepali
1376 Dutch
1379 Norwegian
1393 Occitan
1403 (Afan)Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1525 Telugu
1527 Tajik
1528 Thai
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volapük
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
1313 Latin
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1171 Faroese
1174 French
1181 Frisian
1503 Singhalese
1505 Slovak
1506 Slovenian
1345 Malagasy
1703 Not specified
Parental Control Area Code List
Code Area
Code Area
Code Area
Code Area
2044 Argentina
2047 Australia
2046 Austria
2057 Belgium
2070 Brazil
2079 Canada
2090 Chile
2165 Finland
2174 France
2109 Germany
2248 India
2238 Indonesia
2254 Italy
2276 Japan
2304 Korea
2363 Malaysia
2362 Mexico
2149 Spain
2376 Netherlands
2390 New Zealand
2379 Norway
2499 Sweden
2086 Switzerland
2528 Thailand
2184 United
Kingdom
2427 Pakistan
2424 Philippines
2436 Portugal
2489 Russia
2092 China
2115 Denmark
2501 Singapore
37US
Tabla de contenido
Paso 1: Conexión del televisor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ES
1ES
Conexiones
Al desembalar la unidad, compruebe los accesorios suministrados que se detallan en
“Specifications” del Manual de instrucciones en inglés.
b
• Enchufe los cables firmemente para evitar ruidos no deseados.
• Consulte el manual de instrucciones suministrado con los componentes que va a conectar.
• Asegúrese de desconectar el cable de corriente de cada componente antes de realizar las conexiones.
Paso 1: Conexión del televisor
Conecte este reproductor al monitor del televisor mediante un cable de video. Seleccione el
patrón A o B, de acuerdo con la toma de entrada del monitor, proyector o componente de
audio.
INPUT
L
(blanco)
Cable de audio/video
(suministrado)
A
AUDIO
(rojo)
R
(amarillo)
VIDEO
(amarillo)
(rojo)
(blanco)
Televisor
a VIDEO OUT
(salida video)
a AUDIO OUT (salida audio)
P
B
VIDEO
L
DIGITAL
OUT
VIDEO OUT
COMPONENT
VIDEO OUT
R
Y
P
R
COAXIAL
AUDIO OUT
Reproductor de CD/DVD
a COMPONENT VIDEO
OUT (salida de video del
componente)
(verde)
(rojo)
(azul)
COMPONENT
VIDEO IN
B
Y
(verde)
Cable de video
PB
componente
(azul)
PR
(no suministrado)
(rojo)
Televisor
: Flujo de señal
b
A Tomas de entrada de audio/
video
Conecte el cable de audio suministrado a las tomas
de entrada de audio (I/D) del televisor.
Disfrutará de imágenes de calidad estándar.
Si lo conecta a un televisor de pantalla
panorámica
B Tomas de entrada de video
Según el disco, es posible que la imagen no
quepa en la pantalla del televisor. Para
cambiar la relación de aspecto, consulte la
versión en inglés del Manual de
instrucciones.
componente (Y, PB, PR
)
Este tipo de conexiones proporciona
imágenes de alta calidad con una
reproducción fiel de los colores.
2ES
b
b
No conecte una videograbadora, etc., entre el televisor
y el reproductor. Si pasa las señales del reproductor a
través de la videograbadora, es posible que no reciba
una imagen clara en la pantalla del televisor. Si el
televisor sólo tiene una toma de entrada de audio/
video, conecte el reproductor a esta toma.
• Tras completar la conexión, realice los ajustes
contrario, los altavoces no emitirán el sonido o
bien emitirán un ruido fuerte.
• Los efectos TVS de este reproductor no son
compatibles con esta conexión.
• Para escuchar pistas de sonido DTS, debe utilizar
esta conexión. Las pistas de sonido DTS no se
emiten a través de las tomas AUDIO OUT L/R
aunque ajuste “DTS” en “SI” en Ajuste rápido
Para conectar el componente de audio
Utilice el siguiente patrón.
Reproductor de CD/DVD
PB
VIDEO
L
DIGITAL
OUT
VIDEO OUT
COMPONENT
VIDEO OUT
R
Y
PR
COAXIAL
AUDIO OUT
a DIGITAL OUT (COAXIAL)
(salida digital coaxial)
DIGITAL
OUT
COAXIAL
Cable digital coaxial (no
suministrado)
a la entrada
digital coaxial
Componente de audio que
dispone de un codificador
: Flujo de señal
z
Para la colocación correcta de los altavoces,
consulte el manual de instrucciones suministrado
con los componentes conectados.
Si el componente de audio dispone de
1
2
decodificador Dolby* Digital o DTS* y una
toma de entrada digital, utilice esta conexión.
Podrá disfrutar de los efectos de sonido
envolvente de Dolby Digital (5.1ch) y DTS
(5.1ch).
*1
Fabricado bajo licencia de Dolby Laboratories.
Dolby, Pro Logic y el símbolo de la doble D son
marcas comerciales de Dolby Laboratories.
Fabricado bajo licencia según Patente de los
*2
EE.UU. N° 5.451.942 y otras patentes emitidas y
pendientes en los EE.UU. y el resto del mundo.
DTS y DTS Digital Out son marcas registradas,
y los logos y símbolo de DTS son marcas
comerciales de DTS, Inc. © 1996-2007 DTS,
Inc. Reservados todos los derechos.
3ES
Control del televisor mediante el
control remoto
Puede controlar el nivel del sonido, la fuente
de entrada y el interruptor de alimentación del
televisor Sony con el control remoto
suministrado.
Paso 2: Conexión del
cable de alimentación
Conecte los cables de alimentación del
reproductor y del televisor a una toma de ca.
TV INPUT
(selección
de entrada)
TV (televisor)
TV
PICTURE
NAVI
Paso 3: Preparación del
control remoto
VOL (volumen)
+/–
Botones
numéricos
TIME/TEXT
CLEAR
AUDIO SUBTITLE
MENU
TOP MENU
Se puede controlar el reproductor con el
control remoto suministrado. Inserte dos pilas
tamaño AA (R6) de forma que coincidan sus
extremos 3 y # con las marcas del interior
del compartimiento. Al utilizar el control
remoto, oriéntelo hacia el sensor remoto
del reproductor.
RETURN
DISPLAY
Puede controlar el televisor mediante los
botones que se indican a continuación.
Presionando
Puede
TV [/1
Encender o apagar el
televisor
VOL
(volumen) +/–
Ajustar el volumen del
televisor
TV INPUT
(selección de
entrada)
Cambiar la fuente de entrada
del televisor entre éste y otras
fuentes de entrada
b
• No deje el control remoto en lugares
extremadamente cálidos o húmedos.
• No permita que caigan objetos extraños sobre el
control remoto, especialmente cuando sustituya
las pilas.
b
Según la unidad conectada, podrá controlar el
televisor utilizando algunos o todos los botones del
control remoto suministrado.
• No exponga el sensor del control remoto a la luz
directa del sol ni a dispositivos de iluminación. Si
lo hace, pueden producirse fallas en el
funcionamiento.
• Cuando no vaya a usar el control remoto durante
un tiempo prolongado, extraiga las pilas para
evitar posibles daños por fugas y corrosión.
4ES
Para controlar otros televisores con el
control remoto
También puede controlar el nivel del sonido,
la fuente de entrada y el interruptor de
alimentación de un televisor de otro
proveedor con el control remoto
suministrado.
Si el televisor figura en la tabla que aparece a
continuación, establezca el código del
fabricante correspondiente.
1
Mientras mantiene presionado TV [/1,
presione los botones numéricos para
seleccionar el código del fabricante del
televisor (consulte la tabla que se
proporciona a continuación).
2
Suelte TV [/1.
◆Códigos de televisores controlables
Si aparece más de un código, ingréselos uno
tras otro hasta encontrar el que funciona con
su televisor.
Fabricante
Sony
Número de código
01 (predeterminado)
02
Hitachi
LG/Goldstar/NEC 04
MGA/Mitsubishi 13
Panasonic
Philips
Pioneer
RCA
19
21
16
10
20
18
07
Samsung
Sharp
Toshiba
b
• Al sustituir las pilas del control remoto, es posible
que el código recupere el valor de fábrica. Vuelva
a ajustar el código apropiado.
• Según la unidad que conecte, podrá controlar el
televisor utilizando algunos o todos los botones
del control remoto suministrado.
5ES
Paso 4: Ajuste rápido
Siga los pasos siguientes para realizar el mínimo de ajustes básicos para utilizar el reproductor.
Para saltar un ajuste, presione >. Para volver al ajuste anterior, presione ..
TV
PICTURE
NAVI
TV
INPUT
TIME/TEXT
CLEAR
AUDIO SUBTITLE
MENU
TOP MENU
ENTER
(ingresar)
RETURN
DISPLAY
1
2
Encienda el televisor.
LANGUAGE SETUP
OSD:
ENGLISH
ENGLISH
MENU:
Presione [/1.
El reproductor se enciende.
FRENCH
AUDIO:
SUBTITLE:
SPANISH
PORTUGUESE
3
Cambie el selector de entrada del
televisor para que la señal del
reproductor aparezca en la
pantalla del televisor.
5
6
Presione X/x para seleccionar un
idioma.
El reproductor muestra el menú y los
subtítulos en el idioma seleccionado.
En la parte inferior de la pantalla,
aparecerá “Press [ENTER] to run
QUICK SETUP” (Toque [ENTER] para
AJUSTE RÁPIDO). Si este mensaje no
aparece, seleccione “QUICK”
(RÁPIDO) en “SETUP” (AJUSTE) del
menú de control para ejecutar el ajuste
rápido.
Presione ENTER.
Aparece la pantalla de ajustes que le
permitirá seleccionar la relación de
aspecto del televisor que vaya a conectar.
AJUSTE PANTALLA
4:3 LETTER BOX
4:3 LETTER BOX
4:3 PAN SCAN
16:9
TIPO TV:
4
Presione ENTER sin insertar
ningún disco.
PROTECTOR PANTALLA:
FONDO:
NIVEL NEGRO DE SEÑAL:
NIVEL NEGRO DE SEÑAL (COMPONENT OUT):
PROGRESSIVE (COMPONENT OUT ONLY):
MODALIDAD (PROGRESSIVE):
NO
Aparece la pantalla de ajustes que le
permitirá seleccionar el idioma utilizado
en la pantalla.
NO
AUTO
SALIDA 4:3:
COMPLETO
6ES
7
8
Presione X/x para seleccionar el
ajuste que coincida con el tipo de
televisor.
10Presione X/x para seleccionar el
tipo de señal Dolby Digital que
desee enviar al componente de
audio.
◆ Si tiene un televisor 4:3 estándar
• 4:3 LETTER BOX (tipo buzón) o 4:3
PAN SCAN (exploración PAN)
Si el componente de audio dispone de
decodificador Dolby Digital, seleccione
“DOLBY DIGITAL”. De lo contrario,
seleccione “D-PCM”.
◆ Si tiene un televisor con pantalla
panorámica o uno 4:3 estándar con el
modo de pantalla panorámica
• 16:9
AJUSTE AUDIO
AUDIO DRC:
MEZCLA:
ESTANDAR
DOLBY SURROUND
SI
SALIDA DIGITAL:
DOLBY DIGITAL:
DTS:
Presione ENTER.
DOLBY DIGITAL
DOLBY DIGITAL
D-PCM
Aparece la pantalla de ajustes que le
permitirá seleccionar el tipo de toma
utilizada para conectar su componente de
audio, tal como un amplificador
(receptor).
48kHz/96kHz PCM:
11Presione ENTER.
¿DVD conectado a receptor-amp? Elija
tipo de toma utilizado.
Se selecciona “DTS”.
AJUSTE AUDIO
AUDIO DRC:
SI
ESTANDAR
AUDIO OUTPUT L/R
MEZCLA:
DOLBY SURROUND
DIGITAL OUTPUT
SALIDA DIGITAL:
DOLBY DIGITAL:
DTS:
SI
NO
DOLBY DIGITAL
NO
NO
SI
48kHz/96kHz PCM:
9
Presione X/x para seleccionar
(si existe) el tipo de toma que
utilice para conectar a un
12Presione X/x para seleccionar si
desea o no enviar una señal DTS
al componente de audio.
componente de audio y, a
continuación, presione ENTER.
Si no conectó el componente de audio,
seleccione “NO” y vaya al paso 13.
Si conectó el componente de audio sólo
con un cable de audio, seleccione “SI:
AUDIO OUTPUT L/R” y vaya al paso
13.
Si conectó un componente de audio
mediante un cable digital coaxial,
seleccione “SI: DIGITAL OUTPUT”.
Si el componente de audio dispone de
decodificador DTS, seleccione “SI”. De
lo contrario, seleccione “NO”.
13Presione ENTER.
El ajuste rápido ha finalizado y
conexiones han completado.
7ES
Para detener la reproducción
Presione x.
Reproducción
Para introducir una pausa en la
reproducción
Presione X.
Reproducción de discos
z
El reproductor se puede apagar en forma automática
siempre que lo deje en modo de parada durante más
de 30 minutos. Para activar o desactivar esta
función, ajuste “DESCONEXION
AUTOMATICA” en “AJUSTE
Algunas operaciones pueden ser distintas o
estar limitadas en función del DVD o VIDEO
CD.
Consulte las instrucciones de uso
suministradas con el disco.
PERSONALIZADO” en “SI” o “NO”.
TV
INPUT
TV
PICTURE
NAVI
b
Los discos creados con grabadoras de DVD deberán
estar finalizados correctamente para poder
reproducirse. Para obtener más información acerca
de la finalización, consulte el manual de
instrucciones suministrado con la grabadora de
DVD.
Botones
numéricos
TIME/TEXT
CLEAR
AUDIO SUBTITLE
MENU
TOP MENU
ENTER
(ingresar)
Notas sobre la reproducción de pistas de
sonido DTS de un DVD VIDEO
Las señales de audio DTS se emiten sólo a
través de la toma DIGITAL OUT
(COAXIAL).
RETURN
(volver)
RETURN
DISPLAY
Reanudación de la reproducción a partir
del punto en el que se detuvo el disco
(Reanudación multidisco)
Si vuelve a presionar N después de detener
la reproducción, el reproductor iniciará la
reproducción a partir del punto en el que la
detuvo al presionar x.
1
Presione Z en el reproductor y
coloque un disco en la bandeja de
discos.
z
• Para reproducir el disco desde el principio,
presione x dos veces y, a continuación, presione
N.
• Con discos DVD VIDEO y VIDEO CD, el
reproductor memoriza el punto en el que se
detuvo el disco hasta un máximo de 6 discos y
reanuda la reproducción la próxima vez que
inserte el mismo disco. Si memoriza un punto de
reanudación de reproducción para el disco
número 7, el punto de reanudación de
reproducción del primer disco se borrará.
Con la cara de
reproducción hacia abajo
2
Presione N.
La bandeja de discos se cierra y el
reproductor inicia la reproducción
(continua). Ajuste el volumen en el
televisor o en el componente de audio.
De acuerdo con el disco, puede aparecer
un menú en la pantalla del televisor.
b
• Para que esta opción funcione, se debe ajustar
“REANUDACION MULTIDISCO” de
“AJUSTE PERSONALIZADO” en “SI”
(predeterminado).
• La reanudación de reproducción no funciona
durante la reproducción aleatoria ni la
reproducción de programa.
8ES
• Es posible que en algunos discos la función de
reanudación de la reproducción no funcione,
dependiendo del punto en el que la haya detenido,
o si presiona [/1.
b
Aunque seleccione “RESTAURAR” en “AJUSTE”
del menú de control, la bandeja de discos
permanece bloqueada.
Reproducción de VIDEO CD con funciones
PBC (Reproducción PBC)
La reproducción PBC (Playback Control
(control de reproducción)) permite reproducir
discos VIDEO CD en forma interactiva si
sigue las instrucciones del menú que aparece
en la pantalla del televisor.
Al reproducir un VIDEO CD con funciones
PBC, aparecerá el menú en la pantalla.
Seleccione un elemento con los botones de
números y presione ENTER. Luego, siga las
instrucciones del menú para las funciones
interactivas (presione N cuando aparezca
“Presione SELECT”).
Consulte las instrucciones suministradas con
el disco, ya que el procedimiento de
operación puede variar en función del
VIDEO CD.
Para volver al menú
Presione O RETURN.
z
Para reproducir sin la opción PBC, presione ./
> o los botones numéricos mientras el
reproductor está detenido para seleccionar una pista
y, a continuación, presione N o ENTER.
En la pantalla del televisor aparece “Reproducción
sin PBC” y el reproductor inicia la reproducción
continua. No puede reproducir imágenes fijas,
como un menú.
Para regresar a la reproducción con PBC, presione
x dos veces y, a continuación, presione N.
Bloqueo de la bandeja de discos (Bloqueo
para niños)
Es posible bloquear la bandeja de discos para
evitar que los niños la abran.
Si el reproductor está en modo de espera,
presione O RETURN, ENTER y, a
continuación, \/1 en el control remoto.
El reproductor se enciende y aparece “
”
(LOCKED) (bloqueado) en la pantalla del
panel frontal. El botón Z del reproductor no
funcionará mientras esté activado el bloqueo
para niños.
Para desbloquear la bandeja de discos,
presione O RETURN, ENTER y, a
continuación, \/1 de nuevo cuando el
reproductor está en modo de espera.
9ES
4-115-660-11(1)
Sony Corporation Printed in China
|